Posts Tagged With: Cosplay walkthrough

Elsa From Disney’s Frozen Costume Walkthrough Part 2- SnowFlakes & Glitter

Elsa’s cape/train has this gorgeous snowflake and icicle design. It is quite detailed and requires a lot of time and patience. Unfortunately, I do not have my own magical snow powers so I had to make my train out of glitter instead of snow. Make sure to read part one of my walkthrough to see all the materials I used and where to get them.

Here is a list of the basic Materials:

~ 1 lb of #359 Misty Transparent Ultrafine From Artglitter.com

~ 3-4 bottles of fabric mod podge from local craft store

~ sponge brushes

~ x-acto knife

~ duct tape

~ self healing cutting board

Image

Image

The first thing I did to create the design was grab a bunch of paper to recreate the patterns. For the large icicle designs, I took the concept art (shown above) and made the designs proportional to my personal height. (If you are shorter or taller than 5’8″ I would recommend testing it first). After I calculated those lengths, I grab a bunch of paper and started drawing the design. I only drew half of the design at first so when I transferred it both sides would be exactly the same.

Image

When I was happy with the design I transfer the patterns to sheets of duct tape. WARNING: I do not recommend using duct tape. It is a very aggressive tape and can easily tear and/or leave residue on your fabric. The only reason I used it was because I had a bunch left over from a previous project. I made the sheets of duct tape by taking my self-healing cutting board and laying down rows of duct tape. Then drew a line down the middle, lined up the icicle design, traced the first side, reversed the stencil, and did the same thing on the other side of the line. I cut out the designs with an x-acto knife. I did this a total of about 4 times for all my different stencils (not including all the mess ups lol). You can reuse the duct tape stencils about 2-3 times before it loses all of its adhesives. Note: Duct tape DOES NOT un-stick from itself, wax paper, anything paper, and a lot of plastics.

ImageImage

 

I followed the same basic process to create the snowflake stencils as well. I made a few snowflakes that match Elsa’s cape from the movie and concept art. I folded a piece of paper in half and made the snowflake designs with a ruler. After that I used them as a stencil and transfer them on to the duct tape sheets. For the other snowflakes, I had some paper snowflakes my roommate and I decorated our room with. I bought them at my local craft store called Patcan’s back in November.

Image

After all of the stencils were cut out, it was time to glitter the train to death. I took a sponge brush and applied fabric mod podge onto a small sections at a time ( be forewarned the mod podge dries quickly). Then I took a spoon full of glitter and lightly tapped it onto the area with glue and patted it lightly. Do not worry about putting too much glitter on the design the extra will fall off later. After you let the mod podge set for about 4 – 6 hours you need to seal the glitter. ( Please seal your glitter or you will be a glitter monster and the design will fall off). The best way to seal your glitter is to put another coat of fabric mod podge on top of it. It dries clear and wont ruin the design. The other method is to heat seal the glitter. I personally did not do this so I would suggest looking up how to do that on google. If you get the mod podge in an unwanted area the best way to remove the glitter and glue is to take a q-tip or cotton ball with some nail polish remover and GENTLY scrub off the unwanted. If you are afraid the nail polish remover will damage your fabric be sure to practice on some scrap fabric.

Image

 

Image

Image

Image

Image

Image

Image

Image

So a lot of time later I had this huge train of glitter and snowflakes. It was quite a bit of work but well worth the results. The pictures do not show how sparkly it is person unfortunately. :/

I used the same process for Elsa’s top. I wont go into great detail how I made it but here are the progess photos of the glitter designs on her sleeves.

Image

Image

Image

 

Sorry for the awkward pose in the last photo I was trying to adjust my body so pattern was clearly visible.

Anyways, I hope this helpful to all who requested the walk through! I will be making part 3 – the shoes later this week, probably after my calculus test. Part 4 will be the wig but it is back home so I will have to wait until spring break to take pictures of it. Thanks for reading and have a lovely day! 😀

Categories: Uncategorized | Tags: , , , , , , , , , | 37 Comments

Blog at WordPress.com.